Feisty Fawn - nefunguje WIFI (notebook Acer TM2350)

[Fuzzy]

Používám wifi kartu do pcmcia Gigabyte GN-WLMR101 (RTL8180L). V Kubuntu 6.10 mi jela hned po instalaci systému bez problémů. V 7.04 mě ovšem karta nefunguje, mohli byste mi prosím někdo poradit jak postupovat popřípadě sem dát nějaký link? Díky

[Jakub Lucký]

Mě by se hodilo upřesnit jak nefunguje...
a pár výpisů

dmesg po zapojení, ifconfig apod.

[LS]

Podle vypisu to vypada ze WIFI karta byla spravne detekovana, ovladac zavedeny, a dokonce se to pripojilo do nejake site LukasNet. Pouze protestuje proti chybejici konfiguraci IPv6, co by zde nemelo mit za nasledek uplny vypadek spojeni.

Ciste nahodou: FireHOL nepouzivate?

Ve vypisu jsou mraky chyb komunikace s diskem, zkuste ho zkontrolovat nejakym vhodnym nastrojem. Toto opet nesouvisi s wifi, ale mohlo by se jednat o predzvest nejakych vaznejsich problemu na disku.

[Fuzzy]

jen pro upřesnění... tohle jsou výpisy z 6.10 kde mi vše funguje. Z FF je pošlu co nejdřív. FireHOL nepoužívám.

[Fuzzy]

Výpisy z FF:
ifconfig:

Kód: [Vybrat]

eth0      Link encap:Ethernet  HWaddr 00:0F:B0:7F:7E:F6
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:21 Base address:0x6000

eth0:avah Link encap:Ethernet  HWaddr 00:0F:B0:7F:7E:F6
          inet addr:169.254.9.179  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          Interrupt:21 Base address:0x6000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:16 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1232 (1.2 KiB)  TX bytes:1232 (1.2 KiB)dmesg:

Kód: [Vybrat]

[    0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] sanitize start
[    0.000000] sanitize end
[    0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[    0.000000] copy_e820_map() type is E820_RAM
[    0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[    0.000000] copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
[    0.000000] copy_e820_map() start: 0000000000100000 size: 000000001eef0000 end: 000000001eff0000 type: 1
[    0.000000] copy_e820_map() type is E820_RAM
[    0.000000] copy_e820_map() start: 000000001eff0000 size: 000000000000ffc0 end: 000000001effffc0 type: 3
[    0.000000] copy_e820_map() start: 000000001effffc0 size: 0000000000000040 end: 000000001f000000 type: 4
[    0.000000] copy_e820_map() start: 00000000ffb80000 size: 0000000000080000 end: 00000000ffc00000 type: 2
[    0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
[    0.000000]  BIOS-e820: 000000001eff0000 - 000000001effffc0 (ACPI data)
[    0.000000]  BIOS-e820: 000000001effffc0 - 000000001f000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 495MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 126960) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   126960
[    0.000000]   HighMem    126960 ->   126960
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   126960
[    0.000000] On node 0 totalpages: 126960
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 959 pages used for memmap
[    0.000000]   Normal zone: 121905 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP (v000 OID_00                                ) @ 0x000e6010
[    0.000000] ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI 0x00010101) @ 0x1effa9a0
[    0.000000] ACPI: FADT (v001 ACER   ECL57  " 0x00000100 _CSI 0x00010101) @ 0x1efffaa0
[    0.000000] ACPI: BOOT (v001 INSYDE BOOT_000 0x00000001 _CSI 0x00010101) @ 0x1efffb90
[    0.000000] ACPI: DBGP (v001 INSYDE DBGP_000 0x00000001 _CSI 0x00010101) @ 0x1efffbc0
[    0.000000] ACPI: MADT (v001 INSYDE APIC_000 0x30303030 0000 0x30303030) @ 0x1efffb30
[    0.000000] ACPI: DSDT (v001 ACER   TM4050   0x00000006 MSFT 0x0100000e) @ 0x00000000
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:13 APIC version 20
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 20000000 (gap: 1f000000:e0b80000)
[    0.000000] Detected 1398.851 MHz processor.
[   51.556973] Built 1 zonelists.  Total pages: 125969
[   51.556979] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- locale=cs_CZ console-setup/layoutcode=cz
[   51.557250] mapped APIC to ffffd000 (fee00000)
[   51.557253] mapped IOAPIC to ffffc000 (fec00000)
[   51.557258] Enabling fast FPU save and restore... done.
[   51.557261] Enabling unmasked SIMD FPU exception support... done.
[   51.557273] Initializing CPU#0
[   51.557351] PID hash table entries: 2048 (order: 11, 8192 bytes)
[   51.559285] Console: colour VGA+ 80x25
[   51.559474] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[   51.559718] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[   51.578162] Memory: 492224k/507840k available (1992k kernel code, 15024k reserved, 893k data, 328k init, 0k highmem)
[   51.578174] virtual kernel memory layout:
[   51.578175]     fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
[   51.578177]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   51.578179]     vmalloc : 0xdf800000 - 0xff7fe000   ( 511 MB)
[   51.578180]     lowmem  : 0xc0000000 - 0xdeff0000   ( 495 MB)
[   51.578182]       .init : 0xc03d7000 - 0xc0429000   ( 328 kB)
[   51.578183]       .data : 0xc02f2264 - 0xc03d16d4   ( 893 kB)
[   51.578185]       .text : 0xc0100000 - 0xc02f2264   (1992 kB)
[   51.578189] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   51.657354] Calibrating delay using timer specific routine.. 2799.55 BogoMIPS (lpj=5599109)
[   51.657402] Security Framework v1.0.0 initialized
[   51.657409] SELinux:  Disabled at boot.
[   51.657429] Mount-cache hash table entries: 512
[   51.657590] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000
[   51.657603] CPU: L1 I cache: 32K, L1 D cache: 32K
[   51.657607] CPU: L2 cache: 1024K
[   51.657610] CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000000 00000000 00000000
[   51.657621] Compat vDSO mapped to ffffe000.
[   51.657626] Remapping vsyscall page to ffffe000
[   51.657639] Checking 'hlt' instruction... OK.
[   51.673454] SMP alternatives: switching to UP code
[   51.673639] Freeing SMP alternatives: 11k freed
[   51.673846] Early unpacking initramfs... done
[   52.077473] ACPI: Core revision 20060707
[   52.077598] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[   52.093501] CPU0: Intel(R) Celeron(R) M processor         1.40GHz stepping 08
[   52.093527] Total of 1 processors activated (2799.55 BogoMIPS).
[   52.093660] ENABLING IO-APIC IRQs
[   52.093845] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   52.241394] Brought up 1 CPUs
[   52.241668] Booting paravirtualized kernel on bare hardware
[   52.241741] Time:  9:36:08  Date: 03/25/107
[   52.241773] NET: Registered protocol family 16
[   52.241872] EISA bus registered
[   52.241878] ACPI: bus type pci registered
[   52.241924] PCI: PCI BIOS revision 2.10 entry at 0xe97e4, last bus=1
[   52.241927] PCI: Using configuration type 1
[   52.241929] Setting up standard PCI resources
[   52.244411] ACPI: Interpreter enabled
[   52.244414] ACPI: Using IOAPIC for interrupt routing
[   52.244921] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   52.244927] PCI: Probing PCI hardware (bus 00)
[   52.245840] Boot video device is 0000:00:02.0
[   52.246138] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[   52.246142] PCI quirk: region 1300-133f claimed by ICH4 GPIO
[   52.246435] PCI: Transparent bridge - 0000:00:1e.0
[   52.246489] PCI: Bus #02 (-#05) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses')
[   52.246492] Please report the result to linux-kernel to fix this permanently
[   52.246508] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   52.253881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[   52.254819] ACPI: PCI Interrupt Link [LNKA] (IRQs 10) *11
[   52.255049] ACPI: PCI Interrupt Link [LNKB] (IRQs 10) *5
[   52.255276] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *0, disabled.
[   52.255505] ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
[   52.255743] ACPI: PCI Interrupt Link [LNKE] (IRQs 10) *0, disabled.
[   52.255975] ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *11
[   52.256207] ACPI: PCI Interrupt Link [LNKG] (IRQs 10) *0, disabled.
[   52.256447] ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
[   52.298351] Linux Plug and Play Support v0.97 (c) Adam Belay
[   52.298362] pnp: PnP ACPI init
[   52.321400] pnp: PnP ACPI: found 8 devices
[   52.321405] PnPBIOS: Disabled by ACPI PNP
[   52.321459] PCI: Using ACPI for IRQ routing
[   52.321462] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   52.323464] NET: Registered protocol family 8
[   52.323466] NET: Registered protocol family 20
[   52.323941] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[   52.323958] PCI: Bus 2, cardbus bridge: 0000:01:04.0
[   52.323961]   IO window: 0000c400-0000c4ff
[   52.323966]   IO window: 0000c800-0000c8ff
[   52.323970]   PREFETCH window: a0000000-a3ffffff
[   52.323975]   MEM window: e4000000-e7ffffff
[   52.323979] PCI: Bridge: 0000:00:1e.0
[   52.323983]   IO window: c000-dfff
[   52.323988]   MEM window: e0000000-efffffff
[   52.323993]   PREFETCH window: a0000000-afffffff
[   52.324006] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   52.324023] ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[   52.324055] NET: Registered protocol family 2
[   52.357420] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   52.357513] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[   52.357637] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[   52.357705] TCP: Hash tables configured (established 16384 bind 8192)
[   52.357708] TCP reno registered
[   52.369485] checking if image is initramfs... it is
[   53.170205] Freeing initrd memory: 6965k freed
[   53.170501] Simple Boot Flag at 0x37 set to 0x1
[   53.170774] audit: initializing netlink socket (disabled)
[   53.170794] audit(1177493768.684:1): initialized
[   53.170953] VFS: Disk quotas dquot_6.5.1
[   53.170978] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   53.171036] io scheduler noop registered
[   53.171040] io scheduler anticipatory registered
[   53.171042] io scheduler deadline registered
[   53.171054] io scheduler cfq registered (default)
[   53.171390] isapnp: Scanning for PnP cards...
[   53.525205] isapnp: No Plug & Play device found
[   53.557530] Real Time Clock Driver v1.12ac
[   53.557595] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   53.558392] ACPI: PCI Interrupt 0000:00:1f.6[b] -> GSI 17 (level, low) -> IRQ 17
[   53.558401] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[   53.558478] mice: PS/2 mouse device common for all mice
[   53.559124] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   53.559413] input: Macintosh mouse button emulation as /class/input/input0
[   53.559451] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   53.559456] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   53.559697] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[   53.559888] i8042.c: Detected active multiplexing controller, rev 1.1.
[   53.559934] serio: i8042 KBD port at 0x60,0x64 irq 1
[   53.559940] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   53.559943] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   53.559946] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   53.559949] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   53.560070] EISA: Probing bus 0 at eisa.0
[   53.560078] Cannot allocate resource for EISA slot 1
[   53.560107] EISA: Detected 0 cards.
[   53.590243] TCP cubic registered
[   53.590257] NET: Registered protocol family 1
[   53.590283] Using IPI No-Shortcut mode
[   53.590375] ACPI: (supports S0 S1 S3 S4 S5)
[   53.590423]   Magic number: 3:400:627
[   53.590830] Freeing unused kernel memory: 328k freed
[   53.592422] input: AT Translated Set 2 keyboard as /class/input/input1
[   53.593335] Time: tsc clocksource has been installed.
[   54.844821] Capability LSM initialized
[   54.885729] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   54.885737] ACPI: Processor [CPU0] (supports 8 throttling states)
[   55.379471] usbcore: registered new interface driver usbfs
[   55.379498] usbcore: registered new interface driver hub
[   55.379522] usbcore: registered new device driver usb
[   55.380554] USB Universal Host Controller Interface driver v3.0
[   55.380614] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[   55.380625] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   55.380630] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   55.380835] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   55.380862] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001200
[   55.380977] usb usb1: configuration #1 chosen from 1 choice
[   55.381004] hub 1-0:1.0: USB hub found
[   55.381010] hub 1-0:1.0: 2 ports detected
[   55.460956] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[   55.481493] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 18
[   55.481508] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   55.481513] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   55.481543] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   55.481570] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00001600
[   55.481672] usb usb2: configuration #1 chosen from 1 choice
[   55.481700] hub 2-0:1.0: USB hub found
[   55.481706] hub 2-0:1.0: 2 ports detected
[   55.586054] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
[   55.586070] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   55.586075] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   55.586106] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   55.586134] uhci_hcd 0000:00:1d.2: irq 19, io base 0x00001700
[   55.586232] usb usb3: configuration #1 chosen from 1 choice
[   55.586261] hub 3-0:1.0: USB hub found
[   55.586267] hub 3-0:1.0: 2 ports detected
[    4.012000] Time: acpi_pm clocksource has been installed.
[    4.020000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
[    4.020000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    4.020000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    4.020000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[    4.020000] ehci_hcd 0000:00:1d.7: debug port 1
[    4.020000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    4.020000] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf0080000
[    4.024000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.024000] usb usb4: configuration #1 chosen from 1 choice
[    4.024000] hub 4-0:1.0: USB hub found
[    4.024000] hub 4-0:1.0: 6 ports detected
[    4.132000] SCSI subsystem initialized
[    4.140000] libata version 2.20 loaded.
[    4.144000] ata_piix 0000:00:1f.1: version 2.10ac1
[    4.144000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[    4.144000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 19
[    4.144000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    4.144000] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011100 irq 14
[    4.144000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011108 irq 15
[    4.144000] scsi0 : ata_piix
[    4.308000] ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
[    4.308000] ata1.00: ATA-6: TOSHIBA MK8032GAX, AD001A, max UDMA/100
[    4.308000] ata1.00: 156301488 sectors, multi 16: LBA48
[    4.308000] ata1.00: limited to UDMA/33 due to 40-wire cable
[    4.316000] ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
[    4.316000] ata1.00: configured for UDMA/33
[    4.316000] scsi1 : ata_piix
[    4.764000] usb 3-2: new low speed USB device using uhci_hcd and address 2
[    4.792000] ata2.00: ATAPI, max UDMA/33
[    4.940000] usb 3-2: configuration #1 chosen from 1 choice
[    4.956000] ata2.00: configured for UDMA/33
[    4.956000] usbcore: registered new interface driver hiddev
[    4.960000] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK8032GA AD00 PQ: 0 ANSI: 5
[    4.972000] input: Microsoft Basic Optical Mouse as /class/input/input2
[    4.972000] input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.2-2
[    4.972000] usbcore: registered new interface driver usbhid
[    4.972000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[    4.972000] scsi 1:0:0:0: CD-ROM            QSI      DVD+-RW SDW-082  LX34 PQ: 0 ANSI: 5
[    4.972000] 8139cp 0000:01:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[    4.972000] 8139cp 0000:01:01.0: Try the "8139too" driver instead.
[    4.972000] 8139too Fast Ethernet driver 0.9.28
[    4.972000] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[    4.972000] eth0: RealTek RTL8139 at 0xdf856000, 00:0f:b0:7f:7e:f6, IRQ 21
[    4.972000] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[    4.996000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[    4.996000] sda: Write Protect is off
[    4.996000] sda: Mode Sense: 00 3a 00 00
[    4.996000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.996000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[    4.996000] sda: Write Protect is off
[    4.996000] sda: Mode Sense: 00 3a 00 00
[    4.996000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.996000]  sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[    5.464000] sd 0:0:0:0: Attached scsi disk sda
[    5.468000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.468000] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[    5.492000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    5.492000] Uniform CD-ROM driver Revision: 3.20
[    5.492000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    6.068000] kjournald starting.  Commit interval 5 seconds
[    6.068000] EXT3-fs: mounted filesystem with ordered data mode.
[    6.088000] kjournald starting.  Commit interval 5 seconds
[    6.088000] EXT3-fs: mounted filesystem with ordered data mode.
[    6.840000] ISO 9660 Extensions: Microsoft Joliet Level 3
[    6.912000] ISO 9660 Extensions: RRIP_1991A
[    6.960000] Registering unionfs 20060916-2203
[    6.960000] unionfs: debugging is not enabled
[    6.976000] loop: loaded (max 8 devices)
[    7.080000] squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
[   73.340000] eth0: link down
[   74.476000] Linux agpgart interface v0.102 (c) Dave Jones
[   74.528000] agpgart: Detected an Intel 855 Chipset.
[   74.528000] agpgart: Detected 16252K stolen memory.
[   74.536000] agpgart: AGP aperture is 128M @ 0xb0000000
[   74.704000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   74.748000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   75.172000] NET: Registered protocol family 17
[   76.320000] input: PC Speaker as /class/input/input3
[   76.372000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0
[   76.408000] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[   76.556000] Yenta: CardBus bridge found at 0000:01:04.0 [1025:0071]
[   76.556000] Yenta: Using CSCINT to route CSC interrupts to PCI
[   76.556000] Yenta: Routing CardBus interrupts to PCI
[   76.556000] Yenta TI: socket 0000:01:04.0, mfunc 0x00111c12, devctl 0x46
[   76.656000] iTCO_vendor_support: vendor-support=0
[   76.656000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[   76.656000] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[   76.656000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   76.708000] intel_rng: Firmware space is locked read-only. If you can't or
[   76.708000] intel_rng: don't want to disable this in firmware setup, and if
[   76.708000] intel_rng: you are certain that your system has a functional
[   76.708000] intel_rng: RNG, try using the 'no_fwh_detect' option.
[   76.800000] Yenta: ISA IRQ mask 0x0c30, PCI irq 16
[   76.800000] Socket status: 30000020
[   76.800000] Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05
[   76.800000] pcmcia: parent PCI bridge I/O window: 0xc000 - 0xdfff
[   76.800000] cs: IO port probe 0xc000-0xdfff: clean.
[   76.800000] pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xefffffff
[   76.800000] pcmcia: parent PCI bridge Memory window: 0xa0000000 - 0xafffffff
[   77.376000] ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 17 (level, low) -> IRQ 17
[   77.376000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   77.444000] pccard: CardBus card inserted into slot 0
[   77.444000] yenta EnE: chaning testregister 0xC9, 04 -> 04
[   77.932000] cs: IO port probe 0x100-0x3af: clean.
[   77.936000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   77.936000] cs: IO port probe 0x820-0x8ff: clean.
[   77.936000] cs: IO port probe 0xc00-0xcf7: clean.
[   77.936000] cs: IO port probe 0xa00-0xaff: clean.
[   78.200000] intel8x0_measure_ac97_clock: measured 55433 usecs
[   78.200000] intel8x0: clocking to 48000
[   79.008000] fuse init (API version 7.8)
[   79.564000] Adding 827336k swap on /dev/sda5.  Priority:-1 extents:1 across:827336k
[   87.300000] ACPI: AC Adapter [ACAD] (off-line)
[   87.576000] ACPI: Battery Slot [BAT1] (battery present)
[   87.648000] input: Power Button (FF) as /class/input/input5
[   87.652000] ACPI: Power Button (FF) [PWRF]
[   87.704000] input: Lid Switch as /class/input/input6
[   87.708000] ACPI: Lid Switch [LID]
[   87.756000] input: Power Button (CM) as /class/input/input7
[   87.760000] ACPI: Power Button (CM) [PWRB]
[   87.812000] input: Sleep Button (CM) as /class/input/input8
[   87.816000] ACPI: Sleep Button (CM) [SLPB]
[   87.884000] No dock devices found.
[   87.912000] Using specific hotkey driver
[   88.100000] ibm_acpi: ec object not found
[   88.204000] ACPI: Video Device [GFX0] (multi-head: yes  rom: yes  post: no)
[   88.296000] pcc_acpi: loading...
[   97.772000] lp: driver loaded but no devices found
[   97.864000] ppdev: user-space parallel port driver
[  103.792000] apm: BIOS not found.
[  105.960000] Bluetooth: Core ver 2.11
[  105.960000] NET: Registered protocol family 31
[  105.960000] Bluetooth: HCI device and connection manager initialized
[  105.960000] Bluetooth: HCI socket layer initialized
[  106.248000] Bluetooth: L2CAP ver 2.8
[  106.248000] Bluetooth: L2CAP socket layer initialized
[  106.468000] Bluetooth: RFCOMM socket layer initialized
[  106.468000] Bluetooth: RFCOMM TTY layer initialized
[  106.468000] Bluetooth: RFCOMM ver 1.8
[  108.540000] [drm] Initialized drm 1.1.0 20060810
[  108.592000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[  108.592000] [drm] Initialized i915 1.6.0 20060119 on minor 0
[  108.592000] PCI: Enabling device 0000:00:02.1 (0000 -> 0002)
[  108.592000] [drm] Initialized i915 1.6.0 20060119 on minor 1
[  118.824000] NET: Registered protocol family 10
[  118.824000] lo: Disabled Privacy Extensions
[  118.824000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  256.852000] usb 4-3: new high speed USB device using ehci_hcd and address 3
[  256.984000] usb 4-3: configuration #1 chosen from 1 choice
[  257.168000] usbcore: registered new interface driver libusual
[  257.224000] Initializing USB Mass Storage driver...
[  257.224000] scsi2 : SCSI emulation for USB Mass Storage devices
[  257.224000] usbcore: registered new interface driver usb-storage
[  257.224000] USB Mass Storage support registered.
[  257.224000] usb-storage: device found at 3
[  257.224000] usb-storage: waiting for device to settle before scanning
[  262.224000] usb-storage: device scan complete
[  262.224000] scsi 2:0:0:0: Direct-Access     CANYON   ET1208A          0.00 PQ: 0 ANSI: 2
[  262.224000] SCSI device sdb: 497664 512-byte hdwr sectors (255 MB)
[  262.224000] sdb: Write Protect is off
[  262.224000] sdb: Mode Sense: 00 00 00 00
[  262.224000] sdb: assuming drive cache: write through
[  262.228000] SCSI device sdb: 497664 512-byte hdwr sectors (255 MB)
[  262.228000] sdb: Write Protect is off
[  262.228000] sdb: Mode Sense: 00 00 00 00
[  262.228000] sdb: assuming drive cache: write through
[  262.228000]  sdb: sdb1
[  262.336000] sd 2:0:0:0: Attached scsi removable disk sdb
[  262.336000] sd 2:0:0:0: Attached scsi generic sg2 type 0

[Cyborg]

Řeším také problém s wifi ... network manager se tváří, že je wifi připojená, ale internetové stránky nenabíhají ... a příkaz ping v konzoli na jakoukoliv adresu taky nic nevypisuje. Děkuju moc za případnou pomoc.

dmesg

Kód: [Vybrat]

enabled
[    5.236314] pnp: Device 00:0a activated.
[    5.236488] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[    5.236740] ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[    5.236749] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[    5.236823] mice: PS/2 mouse device common for all mice
[    5.237396] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[    5.237658] input: Macintosh mouse button emulation as /class/input/input0
[    5.237694] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[    5.237698] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    5.237884] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[    5.244782] serio: i8042 KBD port at 0x60,0x64 irq 1
[    5.244789] serio: i8042 AUX port at 0x60,0x64 irq 12
[    5.244925] EISA: Probing bus 0 at eisa.0
[    5.244932] Cannot allocate resource for EISA slot 1
[    5.244936] Cannot allocate resource for EISA slot 2
[    5.244938] Cannot allocate resource for EISA slot 3
[    5.244941] Cannot allocate resource for EISA slot 4
[    5.244943] Cannot allocate resource for EISA slot 5
[    5.244946] Cannot allocate resource for EISA slot 6
[    5.244948] Cannot allocate resource for EISA slot 7
[    5.244951] Cannot allocate resource for EISA slot 8
[    5.244953] EISA: Detected 0 cards.
[    5.275055] TCP cubic registered
[    5.275066] NET: Registered protocol family 1
[    5.275089] Using IPI No-Shortcut mode
[    5.275153] ACPI: (supports S0 S3 S4 S5)
[    5.275203]   Magic number: 3:941:974
[    5.275217]   hash matches device ttyc1
[    5.275600] Freeing unused kernel memory: 328k freed
[    5.275750] Time: tsc clocksource has been installed.
[    5.277943] input: AT Translated Set 2 keyboard as /class/input/input1
[    6.498519] Capability LSM initialized
[    6.539095] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    6.539102] ACPI: Processor [CPU] (supports 8 throttling states)
[    6.541148] ACPI: Thermal Zone [THM0] (46 C)
[    6.929103] usbcore: registered new interface driver usbfs
[    6.929128] usbcore: registered new interface driver hub
[    6.929149] usbcore: registered new device driver usb
[    6.930712] USB Universal Host Controller Interface driver v3.0
[    6.930765] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[    6.930777] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    6.930781] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    6.930948] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    6.930973] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
[    6.931087] usb usb1: configuration #1 chosen from 1 choice
[    6.931113] hub 1-0:1.0: USB hub found
[    6.931120] hub 1-0:1.0: 2 ports detected
[    6.997520] SCSI subsystem initialized
[    7.008297] libata version 2.20 loaded.
[    7.032324] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    7.032329] ACPI: PCI Interrupt 0000:00:1d.1[b] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[    7.032341] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    7.032346] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    7.032373] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    7.032398] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[    7.032502] usb usb2: configuration #1 chosen from 1 choice
[    7.032529] hub 2-0:1.0: USB hub found
[    7.032536] hub 2-0:1.0: 2 ports detected
[    7.044011] Intel(R) PRO/1000 Network Driver - version 7.3.15-k2-NAPI
[    7.044016] Copyright (c) 1999-2006 Intel Corporation.
[    7.136300] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    7.136306] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[    7.136318] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    7.136323] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    7.136354] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    7.136379] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
[    7.136479] usb usb3: configuration #1 chosen from 1 choice
[    7.136510] hub 3-0:1.0: USB hub found
[    7.136517] hub 3-0:1.0: 2 ports detected
[    7.169989] Floppy drive(s): fd0 is 1.44M
[    7.210561] FDC 0 is a National Semiconductor PC87306
[    3.732000] Time: acpi_pm clocksource has been installed.
[    3.732000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[    3.732000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[    3.732000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    3.732000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.732000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[    3.732000] ehci_hcd 0000:00:1d.7: debug port 1
[    3.732000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    3.732000] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000
[    3.736000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.736000] usb usb4: configuration #1 chosen from 1 choice
[    3.736000] hub 4-0:1.0: USB hub found
[    3.736000] hub 4-0:1.0: 6 ports detected
[    3.840000] ata_piix 0000:00:1f.1: version 2.10ac1
[    3.840000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[    3.840000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[    3.840000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    3.840000] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011860 irq 14
[    3.844000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011868 irq 15
[    3.844000] scsi0 : ata_piix
[    4.008000] ata1.00: ata_hpa_resize 1: sectors = 78140160, hpa_sectors = 78140160
[    4.008000] ata1.00: ATA-6: HTS548040M9AT00, MG2OA5BA, max UDMA/100
[    4.008000] ata1.00: 78140160 sectors, multi 16: LBA
[    4.016000] ata1.00: ata_hpa_resize 1: sectors = 78140160, hpa_sectors = 78140160
[    4.016000] ata1.00: configured for UDMA/100
[    4.016000] scsi1 : ata_piix
[    4.336000] ata2.00: ATAPI, max UDMA/33
[    4.372000] usb 2-1: new low speed USB device using uhci_hcd and address 2
[    4.500000] ata2.00: configured for UDMA/33
[    4.500000] scsi 0:0:0:0: Direct-Access     ATA      HTS548040M9AT00  MG2O PQ: 0 ANSI: 5
[    4.504000] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDR8083N 0K03 PQ: 0 ANSI: 5
[    4.508000] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[    4.520000] SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
[    4.520000] sda: Write Protect is off
[    4.520000] sda: Mode Sense: 00 3a 00 00
[    4.520000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.520000] SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
[    4.520000] sda: Write Protect is off
[    4.520000] sda: Mode Sense: 00 3a 00 00
[    4.520000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.520000]  sda:<6>e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0d:60:b1:29:5a
[    4.760000]  sda1 sda2 <<6>usb 2-1: configuration #1 chosen from 1 choice
[    4.784000] usbcore: registered new interface driver hiddev
[    4.796000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[    4.796000]  sda5 >
[    4.796000] sd 0:0:0:0: Attached scsi disk sda
[    4.808000] input: Logitech Optical USB Mouse as /class/input/input2
[    4.808000] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1
[    4.808000] usbcore: registered new interface driver usbhid
[    4.808000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[    4.816000] sr0: scsi3-mmc drive: 10x/24x cd/rw xa/form2 cdda tray
[    4.816000] Uniform CD-ROM driver Revision: 3.20
[    4.816000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    4.820000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    4.820000] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    4.988000] Attempting manual resume
[    4.988000] swsusp: Resume From Partition 8:5
[    4.988000] PM: Checking swsusp image.
[    4.988000] PM: Resume from disk failed.
[    5.048000] kjournald starting.  Commit interval 5 seconds
[    5.048000] EXT3-fs: mounted filesystem with ordered data mode.
[   16.836000] NET: Registered protocol family 17
[   17.352000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   17.352000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   17.420000] Linux agpgart interface v0.102 (c) Dave Jones
[   17.420000] agpgart: Detected an Intel 855PM Chipset.
[   17.436000] intel_rng: FWH not detected
[   17.436000] agpgart: AGP aperture is 256M @ 0xd0000000
[   17.476000] iTCO_vendor_support: vendor-support=0
[   17.476000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[   17.864000] ath_hal: module license 'Proprietary' taints kernel.
[   17.868000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[   17.900000] Yenta: CardBus bridge found at 0000:02:00.0 [1014:0552]
[   17.900000] Yenta: Using INTVAL to route CSC interrupts to PCI
[   17.900000] Yenta: Routing CardBus interrupts to PCI
[   17.900000] Yenta TI: socket 0000:02:00.0, mfunc 0x01d21b22, devctl 0x64
[   17.980000] parport: PnPBIOS parport detected.
[   17.980000] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
[   18.020000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
[   18.020000] serio: Synaptics pass-through port at isa0060/serio1/input0
[   18.076000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[   18.076000] wlan: 0.8.4.2 (0.9.3)
[   18.076000] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[   18.076000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   18.076000] input: PC Speaker as /class/input/input4
[   18.100000] ath_pci: 0.9.4.5 (0.9.3)
[   18.136000] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[   18.136000] Socket status: 30000086
[   18.136000] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
[   18.136000] cs: IO port probe 0x4000-0x8fff: clean.
[   18.136000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   18.140000] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
[   18.140000] Yenta: CardBus bridge found at 0000:02:00.1 [1014:0552]
[   18.140000] Yenta: Using INTVAL to route CSC interrupts to PCI
[   18.140000] Yenta: Routing CardBus interrupts to PCI
[   18.140000] Yenta TI: socket 0000:02:00.1, mfunc 0x01d21b22, devctl 0x64
[   18.296000] irda_init()
[   18.296000] NET: Registered protocol family 23
[   18.392000] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[   18.392000] Socket status: 30000086
[   18.392000] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
[   18.392000] cs: IO port probe 0x4000-0x8fff: clean.
[   18.436000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   18.436000] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
[   18.452000] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[   18.752000] pnp: Device 00:0c activated.
[   18.752000] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[   18.752000] nsc-ircc, chip->init
[   18.752000] nsc-ircc, Found chip at base=0x02e
[   18.752000] nsc-ircc, driver loaded (Dag Brattli)
[   18.752000] IrDA: Registered device irda0
[   18.752000] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[   18.824000] ath_rate_sample: 1.2 (0.9.3)
[   18.828000] wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   18.828000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[   18.828000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   18.828000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[   18.828000] wifi0: mac 5.6 phy 4.1 5 GHz radio 1.7 2 GHz radio 2.3
[   18.828000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[   18.828000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[   18.828000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[   18.828000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[   18.828000] wifi0: Use hw queue 8 for CAB traffic
[   18.828000] wifi0: Use hw queue 9 for beacons
[   18.864000] wifi0: Atheros 5212: mem=0xc0210000, irq=11
[   19.000000] ACPI: PCI Interrupt 0000:00:1f.5[b] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[   19.000000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   19.524000] cs: IO port probe 0x100-0x3af: clean.
[   19.524000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   19.524000] cs: IO port probe 0x820-0x8ff: clean.
[   19.528000] cs: IO port probe 0xc00-0xcf7: clean.
[   19.528000] cs: IO port probe 0xa00-0xaff: clean.
[   19.540000] cs: IO port probe 0x100-0x3af: clean.
[   19.540000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   19.540000] cs: IO port probe 0x820-0x8ff: clean.
[   19.540000] cs: IO port probe 0xc00-0xcf7: clean.
[   19.540000] cs: IO port probe 0xa00-0xaff: clean.
[   19.820000] intel8x0_measure_ac97_clock: measured 55473 usecs
[   19.820000] intel8x0: clocking to 48000
[   19.976000] fuse init (API version 7.8)
[   20.012000] lp0: using parport0 (interrupt-driven).
[   20.036000] Adding 1646620k swap on /dev/disk/by-uuid/6f27253f-65cf-43d4-8b7d-cf7c9f50aacf.  Priority:-1 extents:1 across:1646620k
[   20.188000] EXT3 FS on sda1, internal journal
[   23.836000] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   24.108000] input: TPPS/2 IBM TrackPoint as /class/input/input5
[   24.708000] input: Power Button (FF) as /class/input/input6
[   24.712000] ACPI: Power Button (FF) [PWRF]
[   24.752000] input: Lid Switch as /class/input/input7
[   24.756000] ACPI: Lid Switch [LID]
[   24.792000] input: Sleep Button (CM) as /class/input/input8
[   24.796000] ACPI: Sleep Button (CM) [SLPB]
[   24.848000] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[   24.872000] ACPI: Battery Slot [BAT0] (battery absent)
[   24.884000] ibm_acpi: ThinkPad EC firmware 1RHT66WW-3.00a
[   24.884000] ibm_acpi: IBM ThinkPad ACPI Extras v0.13
[   24.884000] ibm_acpi: http://ibm-acpi.sf.net/
[   24.908000] ACPI: ACPI Dock Station Driver
[   24.952000] ACPI: AC Adapter [AC] (on-line)
[   24.964000] Using specific hotkey driver
[   24.992000] pcc_acpi: loading...
[   31.112000] [drm] Initialized drm 1.1.0 20060810
[   31.128000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   31.132000] [drm] Initialized radeon 1.25.0 20060524 on minor 0
[   31.860000] ppdev: user-space parallel port driver
[   32.708000] IBM machine detected. Enabling interrupts during APM calls.
[   32.708000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   32.708000] apm: overridden by ACPI.
[   32.768000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[   32.768000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[   32.768000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[   32.928000] Non-volatile memory driver v1.2
[   33.000000] input: /usr/sbin/thinkpad-keys as /class/input/input9
[   33.028000] [drm] Setting GART location based on new memory map
[   33.028000] [drm] writeback test succeeded in 2 usecs
[   33.432000] Bluetooth: Core ver 2.11
[   33.432000] NET: Registered protocol family 31
[   33.432000] Bluetooth: HCI device and connection manager initialized
[   33.432000] Bluetooth: HCI socket layer initialized
[   33.468000] Bluetooth: L2CAP ver 2.8
[   33.468000] Bluetooth: L2CAP socket layer initialized
[   33.508000] Bluetooth: RFCOMM socket layer initialized
[   33.508000] Bluetooth: RFCOMM TTY layer initialized
[   33.508000] Bluetooth: RFCOMM ver 1.8
[   61.700000] NET: Registered protocol family 10
[   61.700000] lo: Disabled Privacy Extensions
[   61.700000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   72.132000] ath0: no IPv6 routers present
[  187.320000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[  891.064000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  892.244000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  912.364000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1037.092000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 1047.852000] ath0: no IPv6 routers present
[ 1065.360000] end_request: I/O error, dev fd0, sector 0
[ 1078.424000] end_request: I/O error, dev fd0, sector 0
[ 1078.424000] Buffer I/O error on device fd0, logical block 0
[ 1091.488000] end_request: I/O error, dev fd0, sector 0
[ 1091.488000] Buffer I/O error on device fd0, logical block 0
[ 1104.552000] end_request: I/O error, dev fd0, sector 0
[ 1104.552000] Buffer I/O error on device fd0, logical block 0
[ 1117.616000] end_request: I/O error, dev fd0, sector 0
[ 1117.616000] Buffer I/O error on device fd0, logical block 0
[ 1130.680000] end_request: I/O error, dev fd0, sector 0
[ 1130.680000] Buffer I/O error on device fd0, logical block 0
[ 1143.744000] end_request: I/O error, dev fd0, sector 0
[ 1143.744000] Buffer I/O error on device fd0, logical block 0
[ 1156.808000] end_request: I/O error, dev fd0, sector 0
[ 1156.808000] Buffer I/O error on device fd0, logical block 0
[ 1169.872000] end_request: I/O error, dev fd0, sector 0
[ 1169.872000] Buffer I/O error on device fd0, logical block 0
[ 1172.892000] ath0: no IPv6 routers present
[ 1182.932000] end_request: I/O error, dev fd0, sector 0
[ 1182.932000] Buffer I/O error on device fd0, logical block 0
[ 1196.000000] end_request: I/O error, dev fd0, sector 0
[ 1196.000000] Buffer I/O error on device fd0, logical block 0
[ 1209.080000] end_request: I/O error, dev fd0, sector 0
[ 1209.080000] Buffer I/O error on device fd0, logical block 0
[ 1222.140000] end_request: I/O error, dev fd0, sector 0
[ 1222.140000] Buffer I/O error on device fd0, logical block 0
[ 1235.208000] end_request: I/O error, dev fd0, sector 0
[ 1235.208000] Buffer I/O error on device fd0, logical block 0
[ 1248.280000] end_request: I/O error, dev fd0, sector 0
[ 1248.280000] Buffer I/O error on device fd0, logical block 0
[ 1261.352000] end_request: I/O error, dev fd0, sector 0
[ 1261.352000] Buffer I/O error on device fd0, logical block 0
[ 1274.420000] end_request: I/O error, dev fd0, sector 0
[ 1274.420000] Buffer I/O error on device fd0, logical block 0
[ 1287.496000] end_request: I/O error, dev fd0, sector 0
[ 1287.496000] Buffer I/O error on device fd0, logical block 0
[ 1300.564000] end_request: I/O error, dev fd0, sector 0
[ 1300.564000] Buffer I/O error on device fd0, logical block 0
[ 1313.628000] end_request: I/O error, dev fd0, sector 0
[ 1313.628000] Buffer I/O error on device fd0, logical block 0
[ 1323.944000] ath0: no IPv6 routers present
[ 1326.700000] end_request: I/O error, dev fd0, sector 0
[ 1326.700000] Buffer I/O error on device fd0, logical block 0
[ 1339.764000] end_request: I/O error, dev fd0, sector 0
[ 1339.764000] Buffer I/O error on device fd0, logical block 0
[ 1352.828000] end_request: I/O error, dev fd0, sector 0
[ 1352.828000] Buffer I/O error on device fd0, logical block 0
[ 1365.892000] end_request: I/O error, dev fd0, sector 0
[ 1365.892000] Buffer I/O error on device fd0, logical block 0
[ 1378.956000] end_request: I/O error, dev fd0, sector 0
[ 1378.956000] Buffer I/O error on device fd0, logical block 0
[ 1392.020000] end_request: I/O error, dev fd0, sector 0
[ 1392.020000] Buffer I/O error on device fd0, logical block 0
[ 1405.084000] end_request: I/O error, dev fd0, sector 0
[ 1405.084000] Buffer I/O error on device fd0, logical block 0
[ 1418.260000] end_request: I/O error, dev fd0, sector 0
[ 1418.260000] Buffer I/O error on device fd0, logical block 0
[ 1421.544000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1431.376000] end_request: I/O error, dev fd0, sector 0
[ 1431.376000] Buffer I/O error on device fd0, logical block 0
[ 1444.436000] end_request: I/O error, dev fd0, sector 0
[ 1444.436000] Buffer I/O error on device fd0, logical block 0
[ 1450.944000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 1457.500000] end_request: I/O error, dev fd0, sector 0
[ 1461.696000] ath0: no IPv6 routers present
[ 1470.564000] end_request: I/O error, dev fd0, sector 0
[ 1483.628000] end_request: I/O error, dev fd0, sector 0
[ 1483.628000] Buffer I/O error on device fd0, logical block 0
[ 1496.692000] end_request: I/O error, dev fd0, sector 0
[ 1496.692000] Buffer I/O error on device fd0, logical block 0
[ 1509.760000] end_request: I/O error, dev fd0, sector 0
[ 1509.760000] Buffer I/O error on device fd0, logical block 0
[ 1522.932000] end_request: I/O error, dev fd0, sector 0
[ 1522.932000] Buffer I/O error on device fd0, logical block 0
[ 1536.000000] end_request: I/O error, dev fd0, sector 0
[ 1536.000000] Buffer I/O error on device fd0, logical block 0
[ 1549.112000] end_request: I/O error, dev fd0, sector 0
[ 1549.112000] Buffer I/O error on device fd0, logical block 0
[ 1562.288000] end_request: I/O error, dev fd0, sector 0
[ 1562.288000] Buffer I/O error on device fd0, logical block 0
[ 1575.436000] end_request: I/O error, dev fd0, sector 0
[ 1575.436000] Buffer I/O error on device fd0, logical block 0
[ 1587.640000] ath0: no IPv6 routers present
[ 1588.596000] end_request: I/O error, dev fd0, sector 0
[ 1588.596000] Buffer I/O error on device fd0, logical block 0
[ 1601.760000] end_request: I/O error, dev fd0, sector 0
[ 1601.760000] Buffer I/O error on device fd0, logical block 0
[ 1614.896000] end_request: I/O error, dev fd0, sector 0
[ 1614.896000] Buffer I/O error on device fd0, logical block 0
[ 1628.020000] end_request: I/O error, dev fd0, sector 0
[ 1628.020000] Buffer I/O error on device fd0, logical block 0
[ 1641.088000] end_request: I/O error, dev fd0, sector 0
[ 1641.088000] Buffer I/O error on device fd0, logical block 0
[ 1654.240000] end_request: I/O error, dev fd0, sector 0
[ 1654.240000] Buffer I/O error on device fd0, logical block 0
[ 1667.308000] end_request: I/O error, dev fd0, sector 0
[ 1667.308000] Buffer I/O error on device fd0, logical block 0
[ 1680.456000] end_request: I/O error, dev fd0, sector 0
[ 1680.456000] Buffer I/O error on device fd0, logical block 0
[ 1693.624000] end_request: I/O error, dev fd0, sector 0
[ 1693.624000] Buffer I/O error on device fd0, logical block 0
[ 1706.692000] end_request: I/O error, dev fd0, sector 0
[ 1706.692000] Buffer I/O error on device fd0, logical block 0
[ 1719.800000] end_request: I/O error, dev fd0, sector 0
[ 1719.800000] Buffer I/O error on device fd0, logical block 0
[ 1732.952000] end_request: I/O error, dev fd0, sector 0
[ 1732.952000] Buffer I/O error on device fd0, logical block 0
[ 1746.112000] end_request: I/O error, dev fd0, sector 0
[ 1746.112000] Buffer I/O error on device fd0, logical block 0
[ 1759.272000] end_request: I/O error, dev fd0, sector 0
[ 1759.272000] Buffer I/O error on device fd0, logical block 0
[ 1772.436000] end_request: I/O error, dev fd0, sector 0
[ 1772.436000] Buffer I/O error on device fd0, logical block 0
[ 1785.588000] end_request: I/O error, dev fd0, sector 0
[ 1785.588000] Buffer I/O error on device fd0, logical block 0
[ 1798.724000] end_request: I/O error, dev fd0, sector 0
[ 1798.724000] Buffer I/O error on device fd0, logical block 0
[ 1811.892000] end_request: I/O error, dev fd0, sector 0
[ 1811.892000] Buffer I/O error on device fd0, logical block 0
[ 1825.056000] end_request: I/O error, dev fd0, sector 0
[ 1825.056000] Buffer I/O error on device fd0, logical block 0
[ 1838.184000] end_request: I/O error, dev fd0, sector 0
[ 1838.184000] Buffer I/O error on device fd0, logical block 0
[ 1851.344000] end_request: I/O error, dev fd0, sector 0
[ 1851.344000] Buffer I/O error on device fd0, logical block 0
[ 1864.440000] end_request: I/O error, dev fd0, sector 0
[ 1877.572000] end_request: I/O error, dev fd0, sector 0
[ 1877.572000] Buffer I/O error on device fd0, logical block 0
[ 1890.640000] end_request: I/O error, dev fd0, sector 0
[ 1890.640000] Buffer I/O error on device fd0, logical block 0
[ 1890.640000] cramfs: wrong magic
[ 1903.792000] end_request: I/O error, dev fd0, sector 0
[ 1916.960000] end_request: I/O error, dev fd0, sector 2
[ 1916.972000] EXT3-fs: unable to read superblock
[ 1930.048000] end_request: I/O error, dev fd0, sector 0
[ 1970.564000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 1970.568000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1988.756000] eth0: no IPv6 routers present
[ 2653.424000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 2663.820000] ath0: no IPv6 routers present
[ 2773.448000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 2790.996000] eth0: no IPv6 routers present
[ 2791.856000] ath0: no IPv6 routers present
[ 2944.376000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 2954.560000] ath0: no IPv6 routers present
[ 2962.336000] e1000: eth0: e1000_watchdog: NIC Link is Down
[ 2997.476000] ath0: no IPv6 routers present
[ 3069.244000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3080.160000] ath0: no IPv6 routers present
[ 3099.828000] ath0: no IPv6 routers present
[ 3154.540000] ath0: no IPv6 routers present
[ 3160.084000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3180.920000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3180.996000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3181.000000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 3301.008000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 3311.736000] ath0: no IPv6 routers present
[ 3421.048000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 3426.520000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3462.024000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3474.672000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3476.860000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3572.004000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 3576.940000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 3577.008000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3581.052000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3605.984000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 3605.984000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3616.124000] eth0: no IPv6 routers present
[ 3707.532000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3718.668000] eth0: no IPv6 routers present
[ 3811.340000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3811.344000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 3811.344000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3811.412000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3829.140000] eth0: no IPv6 routers present
[ 3952.100000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3962.120000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3962.124000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 3962.124000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3962.196000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 3982.760000] eth0: no IPv6 routers present
[ 4452.756000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4452.844000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 4454.304000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 4454.308000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4476.884000] eth0: no IPv6 routers present
[ 5787.780000] e1000: eth0: e1000_watchdog: NIC Link is Down
[ 5823.784000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 5823.788000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 5837.896000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 5846.208000] eth0: no IPv6 routers present
[ 6640.576000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 7641.920000] e1000: eth0: e1000_watchdog: NIC Link is Down
[ 7650.164000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 7773.276000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 8017.220000] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
[ 8017.224000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8049.808000] eth0: no IPv6 routers presentifconfig

Kód: [Vybrat]

ath0      Zapouzdření:Ethernet  HWadr 00:05:4E:45:B8:DF  
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:6 dropped:6 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 455 (455.0 b) Odesláno bajtů: 2011 (1.9 KiB)

ath0:avah Zapouzdření:Ethernet  HWadr 00:05:4E:45:B8:DF  
          inet adr:169.254.8.172  Všesměr:169.254.255.255  Maska:255.255.0.0
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1

eth0      Zapouzdření:Ethernet  HWadr 00:0D:60:B1:29:5A  
          inet adr:10.0.0.3  Všesměr:10.0.0.255  Maska:255.255.255.0
          inet6-adr: fe80::20d:60ff:feb1:295a/64 Rozsah:Linka
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:9996 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8806 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:100
          Přijato bajtů: 9383108 (8.9 MiB) Odesláno bajtů: 1082839 (1.0 MiB)
          Vstupně/Výstupní port:0x8000 Paměť:c0240000-c0260000

lo        Zapouzdření:Místní smyčka  
          inet adr:127.0.0.1  Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:354 errors:0 dropped:0 overruns:0 frame:0
          TX packets:354 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          Přijato bajtů: 26131 (25.5 KiB) Odesláno bajtů: 26131 (25.5 KiB)

wifi0     Zapouzdření:NEZNÁM  HWadr 00-05-4E-45-B8-DF-00-00-00-00-00-00-00-00-00-00  
          AKTIVOVÁNO VŠESMĚROVÉ_VYSÍLÁNÍ BĚŽÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:66272 errors:0 dropped:0 overruns:0 frame:7123
          TX packets:8267 errors:0 dropped:6 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:199
          Přijato bajtů: 6024682 (5.7 MiB) Odesláno bajtů: 422845 (412.9 KiB)
          Přerušení:11

[LS]

fuzzy, Cyborg: prosim poslete vypis "lspci -vv"

[Cyborg]

lspci -w mi hlásí špatný parametr, tak tuším, že jsi myslel -v:

lspci -v

Kód: [Vybrat]

00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
        Subsystem: IBM Unknown device 0529
        Flags: bus master, fast devsel, latency 0
        Memory at d0000000 (32-bit, prefetchable) [size=256M]
        Capabilities:

00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03) (prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, fast devsel, latency 96
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: c0100000-c01fffff
        Prefetchable memory behind bridge: e0000000-e7ffffff

00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at 1800 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at 1820 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at 1840 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: bus master, medium devsel, latency 0, IRQ 11
        Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
        Capabilities:

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=08, sec-latency=168
        I/O behind bridge: 00004000-00008fff
        Memory behind bridge: c0200000-cfffffff
        Prefetchable memory behind bridge: e8000000-efffffff

00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
        Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at 01f0 [size=8]
        I/O ports at 03f4 [size=1]
        I/O ports at 0170 [size=8]
        I/O ports at 0374 [size=1]
        I/O ports at 1860 [size=16]
        Memory at 50000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
        Subsystem: IBM Thinkpad R50e model 1634
        Flags: medium devsel, IRQ 11
        I/O ports at 1880 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
        Subsystem: IBM Unknown device 0537
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at 1c00 [size=256]
        I/O ports at 18c0 [size=64]
        Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
        Memory at c0000800 (32-bit, non-prefetchable) [size=256]
        Capabilities:

00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01) (prog-if 00 [Generic])
        Subsystem: IBM Unknown device 0525
        Flags: medium devsel, IRQ 11
        I/O ports at 2400 [size=256]
        I/O ports at 2000 [size=128]
        Capabilities:

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] (prog-if 00 [VGA])
        Subsystem: IBM Unknown device 0530
        Flags: bus master, stepping, fast Back2Back, 66MHz, medium devsel, latency 66, IRQ 11
        Memory at e0000000 (32-bit, prefetchable) [size=128M]
        I/O ports at 3000 [size=256]
        Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
        [virtual] Expansion ROM at c0120000 [disabled] [size=128K]
        Capabilities:

02:00.0 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01)
        Subsystem: IBM Unknown device 0552
        Flags: bus master, medium devsel, latency 168, IRQ 11
        Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: e8000000-ebfff000 (prefetchable)
        Memory window 1: c4000000-c7fff000
        I/O window 0: 00004000-000040ff
        I/O window 1: 00004400-000044ff
        16-bit legacy interface ports at 0001

02:00.1 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01)
        Subsystem: IBM Unknown device 0552
        Flags: bus master, medium devsel, latency 168, IRQ 11
        Memory at b1000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=07, subordinate=07, sec-latency=176
        Memory window 0: ec000000-effff000 (prefetchable)
        Memory window 1: c8000000-cbfff000
        I/O window 0: 00004800-000048ff
        I/O window 1: 00004c00-00004cff
        16-bit legacy interface ports at 0001

02:01.0 Ethernet controller: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile) (rev 03)
        Subsystem: IBM PRO/1000 MT Mobile Connection
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
        Memory at c0240000 (32-bit, non-prefetchable) [size=128K]
        Memory at c0200000 (32-bit, non-prefetchable) [size=64K]
        I/O ports at 8000 [size=64]
        [virtual] Expansion ROM at c0220000 [disabled] [size=64K]
        Capabilities:

02:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
        Subsystem: Unknown device 17ab:8331
        Flags: bus master, medium devsel, latency 168, IRQ 11
        Memory at c0210000 (32-bit, non-prefetchable) [size=64K]
        Capabilities:

[LS]

nemyslel jsem ani -w ani -v, ale -vv, presne jak jsem napsal
V kazdem pripade i z tohoto vypisu je videt, ze vase wifi karta je

Kód: [Vybrat]

Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)zkusim se podivat, jak jse to s jeji podporou v aktualnim Ubuntu.

[Cyborg]

OK, díky! Mám ve Firefoxu takové písmo, že -vv, vypadá fakt úplně, jako -w.

A kam se na to díváš? Abych byl moudřejší...

[Fuzzy]

lspci -vv

Kód: [Vybrat]

00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/
O Controller (rev 02)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Latency: 0
        Region 0: Memory at (32-bit, prefetchable)
        Capabilities:

00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor
 to I/O Controller (rev 02)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Latency: 0

00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor
 to I/O Controller (rev 02)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Latency: 0

00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Grap
hics Device (rev 02) (prog-if 00 [VGA])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at b0000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=512K]
        Region 2: I/O ports at e000 [size=8]
        Capabilities:

00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics De
vice (rev 02)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Region 0: Memory at 20000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at 28000000 (32-bit, non-prefetchable) [size=512K]
        Capabilities:

00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) U
SB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at 1200 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) U
SB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin B routed to IRQ 18
        Region 4: I/O ports at 1600 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) U
SB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin C routed to IRQ 19
        Region 4: I/O ports at 1700 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Co
ntroller (rev 03) (prog-if 20 [EHCI])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin D routed to IRQ 20
        Region 0: Memory at f0080000 (32-bit, non-prefetchable) [size=1K]
        Capabilities:

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) (prog-if
00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR-         Latency: 0
        Bus: primary=00, secondary=01, subordinate=05, sec-latency=32
        I/O behind bridge: 0000c000-0000dfff
        Memory behind bridge: e0000000-efffffff
        Prefetchable memory behind bridge: a0000000-afffffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- -         BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (re
v 03)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 0
3) (prog-if 8a [Master SecP PriP])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at 1100 [size=16]
        Region 5: Memory at 28080000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Cont
roller (rev 03)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Interrupt: pin B routed to IRQ 255
        Region 4: I/O ports at 1400 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH
4-L/ICH4-M) AC'97 Audio Controller (rev 03)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at e100 [size=256]
        Region 1: I/O ports at e200 [size=64]
        Region 2: Memory at f0080400 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at f0080600 (32-bit, non-prefetchable) [size=256]
        Capabilities:

00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Mode
m Controller (rev 03) (prog-if 00 [Generic])
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at e300 [size=256]
        Region 1: I/O ports at e400 [size=128]
        Capabilities:

01:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139
C+ (rev 10)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 128 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 21
        Region 0: I/O ports at c000 [size=256]
        Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=256]
        Capabilities:

01:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
        Subsystem: Acer Incorporated [ALI] Unknown device 0071
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- - SERR-         Latency: 168, Cache Line Size: 128 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: a0000000-a3fff000 (prefetchable)
        Memory window 1: e4000000-e7fff000
        I/O window 0: 0000c400-0000c4ff
        I/O window 1: 0000c800-0000c8ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
        16-bit legacy interface ports at 0001

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8180L 802.11b MA                                                              C (rev 20)
        Subsystem: Giga-byte Technology Unknown device e880
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Step                                                              ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-         Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at c400 [disabled] [size=256]
        Region 1: Memory at e4000000 (32-bit, non-prefetchable) [disabled] [size                                                              =512]
        Capabilities:

[Fuzzy]

znamená tahle část že systém nemá na moji wifinu ovladač??  Proč ho EE měl a v FF už není?

Kód: [Vybrat]

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8180L 802.11b MA                                                              C (rev 20)
        Subsystem: Giga-byte Technology Unknown device e880
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Step                                                              ping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-         Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at c400 [disabled] [size=256]
        Region 1: Memory at e4000000 (32-bit, non-prefetchable) [disabled] [size                                                              =512]
        Capabilities:

[LS]

Cyborg: tezko rict, tomuhle cloveku to nechodi, tomuhle ano

fuzzy: problem s vasim typem karty se resi zde

[Fuzzy]

Děkuju za pohotovou odpověď, zkusím to nějak přelouskat a snad se mi to nějak povede rozjet.. jinak zůstanu u 6.10 (což ovšem není řešení).

[vadimo]

Ja si vždy odinštalujem network manager, lebo mi robí problémy. A sieť si aj tak konfigurujem ručne.

[Cyborg]

Cyborg: tezko rict, tomuhle cloveku to nechodi, tomuhle ano

U mě nakonec byl problém v nastavení AP, kde jsem měl zvoleno "hide SSID" ... kvůli tomu nejprve nebylo vidět AP vůbec (logicky) ale našel jsem ho pomocí balíčku Wifi-radar. I potom ale neproběhlo připojení. Takže to asi network manageru vadí...

Teď jsem stejně spokojený s FF, jako ten druhý chlapík. WIFI kartu Ubuntu rozeznalo samo a nainstalovalo ovladače. Heslo stačí zadat jen jednou a uložit do Správce klíčenek. Jediné co nefunguje je klávesová zkratka Fn+F5, která by měla wifi odpojit, ale to už je do jiného vlákna. Díky

[LS]

Hm, je pravda ze nejste prvni, kdo hlasi problem s prihlasenim do site se skrytym ESSID.

[minsan]

Taky používám skryté SSID, nechtělo se to připojit k nalezené síti "hide SSID", tak jsem musel tu nalezenou síť přepsat na skutečný název sítě - asi to hned napadne každého, jen mi to trochu trvalo . Teď už to funguje bez problémů.